I have scoured the net with various keywords and nobody has actually stated what the purpose of the rubber sleeve is on the bottom of a caliper pin. I'm not sure all disc brakes have it, but some do and in some cases the rubbersleeved pin goes at the top. If it helps lubricate, why doesn't the bottom one have it? I've also run upon people with seized pins and it's because the rubber can toughen up or expand and lock in place. Wouldn't it disproportionately stiffen one pin vs the other leading to uneven braking?

#bundysgarage # calipepin #discbrakes

Finally, mine are a bit screwed, so I plan on making new rubber sleeves with some tubing from lowes (I'll dremel wheel the matching grooves in place). Any potential problem with that, assuming I can find the right fit?

The little rubber thing maybe 5 mm thick that goes in a grove at the end of the caliper pin. A couple months ago I refurbed my front brakes and had the same question. The two packs of new pins I bought had the slots for the rubber thing on one pack, but the other had no slot. I ended up not putting any of the rubber things on. It seemed like most of the reason my calipers were seizing up was that rubber thing breaking up and getting stuck in the sliding area. So far I haven't noticed a problem.

It may have to do with squealing but I know these cause problems for some people as they can get very tight and greatly limit movement of the pin. Using a rubberdestructive grease will certainly come into play here.

On toyota/scion vehicles, there are rubber oring bushings on some of the sliding pins for the calipers. On the front, only the bottom one I believe has it... On the rear, both do if I remember correctly.

When I did my brakes a few months ago I had big problems with the pins seizing up in the rear. Once I got them unstuck, cleaned, relubed, replaced the pins and bushings, etc... I noticed there was much more resistance with the bushings on (I am sure by design)... Because the calipers were all seized up, there is more resistance than normal I believe.

Either way, they did slide properly after the fact but not as easily as the front ones. I removed the bushings and tested the operation without and they worked extremely well with little to no resistance at all.

But I figured that bushing had to be there for a reason so I made sure to keep them in and just lubed up as much as I could with silglyde (the permatex purple stuff seized them shortly after the first time... Don't use that stuff with any rubber).

My question is, are those bushings absolutely necessary? I plan to check/lube the brakes before winter again and want to hear some opinions on these... If they help the rear brakes function better (less resistance with the pins) should I remove them? When doing my dad's Prius brakes, I noticed his rear brakes had the slot for the bushings, but with no bushings present (nobody ever serviced them before me). So I am guessing it won't cause any damage if Toyota practice this on their other vehicles.

Just looking for some thoughts though... What is the function of these bushings anyway? Noise?

Caliper slide pin rubber at the end articles:

https://bit.ly/2M460II

https://bit.ly/2YKKK0o

https://bit.ly/2M2NIY6

https://bit.ly/2ZwbO0u



More About BundysGarage:
https://goo.gl/qv3Wzc

Questions, Comments, Concerns:
[email protected]

Twitter:
  / bundysgarage  
@bundysgarage

On The Web:
http://www.bundysgarage.com

Music by Randall Kent: As seen on NCIS
   • Randall Kent  Going Home (Featured o...  

All Rights Reserved 2019
© Copyright 2019
Bundys Garage

All rights reserved. This material may not be published, broadcast, rewritten or redistributed in whole or part with out the express written permission. Contact: [email protected]

DISCLAIMER DISCLAIMER DISCLAIMER

Due to factors beyond the control of BundysGarage, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. BundysGarage assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. BundysGarage recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of BundysGarage, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the end user and not BundysGarage nor any of it’s subsidiaries.