Ask This Old House carpenter Nathan Gilbert travels to Missouri to install a set of bypass doors for a pantry.

#ThisOldHouse #AskTOH
SUBSCRIBE to This Old House: http://bit.ly/SubscribeThisOldHouse

Time: 34 hours

Cost: $150

Skill Level: Moderate

Tools:
Drill driver [https://amzn.to/35X3hYs]
Forstner bit [https://amzn.to/2LpDxKP]
Level [https://amzn.to/2WqNcXQ]
Measuring tape [https://amzn.to/2WSIS2H]
Track saw [https://amzn.to/2zwrcC6]
Brad nailer [https://amzn.to/2WRJoOu]

Shopping List:
Primed trim piece [https://thd.co/2WrCW1u]
Interior doors [https://thd.co/2SYElKU]
Bypass door hardware kit [https://amzn.to/2LrnRqs]
Shims [https://amzn.to/2WRjt9D]

Steps for installing bypass doors:
1. Start by prepping the opening of the doors. In some cases, it might be necessary to pad the opening with some primed 2x stock material to ensure the opening is the exact width as the width of the doors. If the width of the opening is the correct dimension, notch out the opening to accept the trim piece, which will be added later to hide the track once its installed.
2. Hold the track up to the top of the opening and mark the holes for the screws.
3. Remove the track and drill pilot holes on the marks.
4. Secure the track to the top of the opening using screws that come with the kit.
5. Check the track for level. If it’s out of level, the top of the opening can be padded out with a few shims.
6. Hang the roller hardware into the track. Measure from the bottom of the floor to the hardware. Subtract ½” to allow for some clearance for the door.
7. Transfer that measurement to each door and cut the door to size using the track saw. Be sure to cut off material from the bottom of each door.
8. Mount the roller hardware to the door about 1” in on both sides with the drill driver and provided screws.
9. Hang the doors on the track.
10. Place the floor guide on the floor and place the doors in each slot. Once the floor guide is in a good location, secure it to the floor with screws.
11. Drill a hole in each door using a Forstner bit to accept a finger pull that comes with the kit. This will allow the doors to be easily opened and closed.
12. Attach the trim piece in the two notches that were cut in the opening to hide the track. Secure them with a brad nailer.

Resources:
Nathan installed two JELDWEN Colonist Primed wood interior doors [https://thd.co/2SYElKU] that most closely matched the dimensions of the opening. Nathan recommends ensuring the door has not been prehung and does not have bore holes in it for a standard knob. These doors can be found at home centers.

To make the doors bypass, Nathan mounted a Bypass Door Hardware kit [https://amzn.to/2LrnRqs], which is manufactured by Johnson Hardware (https://www.johnsonhardware.com/). The kit comes with all the hardware required to mount the doors.

All the other tools and materials required to install these doors can be found at home centers.

About Ask This Old House TV:
Homeowners have a virtual truckload of questions for us on smaller projects, and we're ready to answer. Ask This Old House solves the steady stream of home improvement problems faced by our viewers—and we make house calls! Ask This Old House features some familiar faces from This Old House, including Kevin O'Connor, general contractor Tom Silva, plumbing and heating expert Richard Trethewey, and landscape contractor Jenn Nawada.

Follow This Old House and Ask This Old House:
Facebook: http://bit.ly/ThisOldHouseFB
Twitter: http://bit.ly/ThisOldHouseTwitter
http://bit.ly/AskTOHTwitter
Pinterest: http://bit.ly/ThisOldHousePinterest
Instagram: http://bit.ly/ThisOldHouseIG
Tumblr: http://bit.ly/ThisOldHouseTumblr

Keywords:
This Old House, Ask This Old House, DIY, Home Improvement, DIY Ideas, Renovation, Renovation Ideas, How To Fix, How To Install, How To Build

Watch the full episode:
https://www.thisoldhouse.com/season1...

How to Install Bypass Pantry Doors | Ask This Old House
   / thisoldhouse