In this video I show how to remove a drill chuck from the DeWalt DCD797. I wanted to make this video after trying to find a solution to my broken chuck. I looked all over and found nothing that could help me. The most common diy removal method is to remove the chuck's set screw (or not) depending on the model, inserting a large allen wrench into the chuck, hand tight, set the drill in lowest gear, set drill to drill mode, lay on side and hit the allen key with a hammer counter clockwise to remove the chuck. I did try this method however after banging on the allen for about 20 mins I decided to just remove the chuck. I got the idea from a youtube video of someone disassembling a dewalt drill. In the video the shaft that holds the chuck just slides right out of the gear housing. I thought why not just remove the chuck in the same manor however instead of breaking down the drill just pull the chuck straight out...and it worked!
DCD791/796 compact drill and hammer drill, and the DCD991/996 3speed drill and hammer drill.
This is a link to the chuck shown in that video

https://www.amazon.com/dp/B00DD7KUXO?...
Keyless Drill Chuck Extra80RV13 Röhm 1328310 for Milwaukee, DeWalt and Makita, 1/2"20" Mount, 1/16"1/2" Capacity with Retaining Ring, TroughHole, Metal

May work with DC901KL DCD995M2 DCD995B DCD985M2
DCD985B DCD970KL DCD795D2 DCD785C2 DCD959KX DCD950KX DCD950B DCD775KL DCD775B DC725KA DCD930KX DCD990M2 DCD980M2 DCD940KX DCD960KL DCD790D2 DCD790B DCD780C2 DCD780B DCD760KL DCD760B DC720KA DCD920KX DC730KA DCD710S2 DCD910KX DC7DCF895M2 DCF895D2 DCF895B DCF886M242KA DC750KA DCF886D2 DCF886B DCF885M2 DCF885C2
DCF885B DC827KL DC825KA DC825B DC835KA DCF815S2 DC845KA
DC800KL DCF889M2 DCF889B DCF889HM2 DCF059KL DW059K2 DW059B DW059HK2 DC821KA DC821B DCF880M2 DCF880B
DCF880HM2 DCF883M2 DCF883B DC233KL DCH253M2 DCH253B
DC212KL DC212KA DC212B DCD771 DCD777 DCD778 DCD780 DCD785
DCD708 DCD709 DCD791 DCD796 DCD991 DCD996 DCD998
Repair to a DeWALT DCD 771 1/2inch Cordless Drill Driver that chuck continues to loosen when used resulting in drill bit loosening and falling out. Ordered online a replacement chuck after a few attempts to remedy the chuck not holding tightly. Drill chucks are critical to the operation of the tool and ours is bent all out of whack so we're going to replace it! However, in order to do that we'll have to get the old chuck off of the tool and that ends up being a bit of a difficult operation. Lets see what we can do! The drill is a Dewalt DCD771 20v Max cordless model, and the new chuck is a Dewalt The keyless chuck Is jammed on my cordless drill. This video will show you how to release a jammed Chuck on any cordless drill with a keyless Chuck.My drill bit got stuck in the chuck, this is just a quick video on how I fixed the keyless chuck on my dewalt drill. If you have a chuck that has jammed then this video may be useful.
This was way better than sending in for repair and the hassle of not having your drill for a period . After using this method I have had no problems with the chuck since. Worth a try but don't hit that chuck too hard. If a slight tap doesn't free up the chuck then there may be another problem there and the drill may have to go for repair. How to Use a Drill/Driver, Impact Driver, & Hammer Drill and How They're DifferentLearn how to use a drill/driver, impact driver, and hammer drill. DCD777 / DCD796 / DCD996: Chucks how not to take them off
This is a hot new take on completely ruining a drill. NEW DeWALT XR It's not a 976 because that's a myth How to remove chuck on cordless drill. Easy way to open a jammed chuck and get stuck drill bit out
How to REMOVE and REPLACE a chuck on a Dewalt DCD791, dcd796, dcd777 and dcd996 cordless drill , make without center screw. Reemplazar el portabrocas Dewalt dcd791. Dewalt DCD791. Chuck, easy replace, «no center screw» Do I fully strip down your Dewalt DCD996 I go into full detail showing how to tear the Dewalt 18v battery drill, showing which screws to remove and even which stickers to remove for a clean strip down. The video also details the safe removal and fitting of a new replacement chuck for the Dewalt 18v DCD996 drill on how to remove the drive spindle from the chuck and also how to remove the chuck from the gearbox. This particular drill chuck is specific to DeWALT manufactured brands, including DeWALT and PorterCable. If your cordless hammer drill is showing any of these symptoms; replacing the keyless chuck could solve your problem: 1) Drill bits slipping or falling out of chuck 2) Chuck won’t open or close 3) Chuck jaws (teeth) damaged 4) Chuck seized onto spindle 5) Chuck is difficult to rotate Get modelspecific repair help from eReplacementParts.com. Learn how to troubleshoot, diagnose and repair your power tools and equipment with illustrated instructions, hundreds of stepbystep repair videos, and our DIY forum.