Welcome back, folks! This time we make an Arduinobased RC Flying wing out of foam, with 3ch of 2 servos and a brushless motor on board, no extended fuselage or tail, simply a cool flying wing! As this is an intermediatebuilder project, it may require that you have some background knowledge of using an Arduino board, and some basic knowledge of electronics.

Hang around until the end of the video to see whether this thing can fly!

Thanks for watching! If you enjoyed watching this video, kindly give a thumbs up, share, comment, and a subscription to the channel to see more similar content.

Visit my online Storefront: https://sites.google.com/view/maximag...

☕ Buy me a coffee: https://www.buymeacoffee.com/MaxImagi...

Instagram: @max.imagination https://www.instagram.com/max.imagina...
Instructables page: https://www.instructables.com/member/...

Disclaimer: Amazon purchase links below are affiliate links. It doesn't cost you extra to buy through those and I just get a tiny commission. Thank you!

Before recreating the plane, (if you are to choose an Arduino flight controller setup like my own) check out my previous video which shows how to make your own RC Arduino 7channel Transmitter:
   • Build an Arduino Radio Transmitter & ...  

Circuit diagram Receiver/FC (credits to Electronoobs) https://electronoobs.com
/eng_arduino_tut25_2.php

Codes TX & RX NRF24L01 Arduino plane codes https://drive.google.com/drive/folder...

Learn more about the NRF24L01 Transceiver https://howtomechatronics.com/tutoria...

Blueprints of the foam flying wing in PDF https://drive.google.com/file/d/1WAnE...

Flying wing design with measurements & CG location https://drive.google.com/file/d/1JoqF...

Center of Gravity (CG) calculator website https://fwcg.3dzone.dk/

Purchase links to parts used in the project: (Parts count ("x..") in reference to the quantity required, actual purchase quantity may vary)
(x1) Brushless Motor 7000Kv 12S EMAX https://amzn.to/3JJqwch
(x1) Plane propeller 5" https://amzn.to/3vQivN4
(x1) Brushless Electronic Speed Controller (ESC)
https://amzn.to/3zJHMtt
(x1) Arduino Nano board https://amzn.to/3dizYqW
(x1) NRF24L01 100M RF Transceiver module https://amzn.to/3BQzKSn
(Optional) NRF24L01 + PNA + LNA RF Transceiver module (longer range) https://amzn.to/3JEoOsV
(x1) Voltage Regulator 3.3V AMS1117 https://amzn.to/3JGJxMu
(x1) Perforated Prototyping board 3x7cm https://amzn.to/3Pa6GIA
(x2) Servo Motors 9G https://amzn.to/3QyORDQ
(x1) LiIon Battery 7.4V 800mAh (Higher capacity, same weight as battery seen in video)
https://amzn.to/3dj3oFn
Female & Male Pin headers https://amzn.to/3Qej2Rg
(x1) 5mm Posterboard foam core sheet for fuselage & wing tip fins 12x9" https://amzn.to/3BYqFXP
(x1) Styrofoam (Polystyrene) insulative foam board sheet for the plane 1.5"
(x2) Paperclip
(x2) Mini zip ties
Clear tape 2" roll (for Lamination of the wing)
Kapton tape (used to make 6 sporty stripes)
(x2) Wooden dowel 5mm stick
(x2) Bamboo Skewer 3mm stick
(x4) Popsicle stick
0.25mm Nichrome wire (Hotwire tool)
Simple wooden bowshaped frame (Hotwire tool)
(x1) Selfthreading wood screws (Hotwire tool)
(18 AWG or thicker) Enameled wire (Hotwire tool)
(x1) Small retraction spring
(x1) Pushbutton momentary switch 3A

Tools and extra supplies I use:
➡ Soldering Iron Kit https://amzn.to/3X6L5Wq
➡ Hot Glue Gun https://amzn.to/3E6trJG
➡ Drill Machine https://amzn.to/3EDe0u8
➡ Box cutter/Utility knife https://amzn.to/3hP9MGI
➡ XActo Hobby Knife https://amzn.to/3XbL7ML
➡ Cutting Matt (Green) https://amzn.to/3gil71A
➡ Needlenose Pliers https://amzn.to/3ECTKc3
➡ Wire Cutters for Electronics https://amzn.to/3ECut1B
➡ Wirestripping tool (Automatic) https://amzn.to/3hQsMVD
➡ Screwdriver kit https://amzn.to/3V6vgNX
➡ Heatshrink Tube Kit https://amzn.to/3AksTPE
➡ Jumper Wire Kit https://amzn.to/3UGhMZq
➡ Breadboard for Prototyping https://amzn.to/3GlF4ze
➡ Perf Boards, Pin headers, and Connectors Kit https://amzn.to/3AkySUw
➡ Superglue https://amzn.to/3EE6uis
➡ Duct Tape https://amzn.to/3g5mTU0
➡ Doublesided Tape https://amzn.to/3Edta82
➡ Kapton Tape (for battery leads) https://amzn.to/3X58bNl

Music credits:

Song: Kuty Boi Beachside Babe
Video's Link:    • Kuty Boi  Beachside Babe [Free Chill...  

Song: ELKAA Ocean
Video's Link:    • ELKAA  Ocean [Free Chill Trap]  

#arduinoproject #flyingwing #arduinonano #maximagination