In this video I take you step by step through the process of converting the front end of your 5th gen 4runner limited to the TRD pro style front end.

Please share your experiences/suggestions in the comments section to help others. I'll try my best to answer any questions you may have as well

Make sure to replace the passenger side air deflector with part number below (not shown in vid)

Only attempt to paint your front bumper if you have previous experience spray bombing
You will need 12 cans of primer, 2 cans of matched base coat (from auto paint store), 23 cans of 2k clear coat.
www.Partify.com or a local autobody shop is a good safe route to have your bumper painted

List of Parts Needed
Note: Some of these parts/clips were ordered from Rock Auto. As mentioned in the video, Rock Auto offers off brand parts/numbers when you enter Toyotas part numbers. Many of these off brand parts have built in clips/retainers. If you go the Toyota branded route you may require more clips to secure the grille and fog lamb bezels. I would recommend purchasing the bumper cover, fog light bezel, and grille and test fitting everything together before hand to see how many clips you require for your conversion. You will likely have extra clips as you can reuse a lot of the originals, but better too many than too little

If you have TSS (2020 or newer) you will need a special grille that accommodates the sensor. Contact Toyota for correct part number(s).

TRD Bumper Cover: 5211935914 has
SR5 Bumper Cover: 5211935918
9046707201 Bumper Cover Clip x5
5211635140 Bumper Cover Retainer x5
9046705138 Bumper Cover Nut Left x2
9015960215 Bumper Cover Screw Left/Right x2

5212735100 Fog Lamp Bezel Right
5212835080 Fog Lamp Bezel Left
7539235220 Fog Lamp Bezel retainer Right x2 or DORMAN 963648
75392 35220 Fog Lamp Bezel Retainer Left x2 OR DORMAN 963648

5311235060 Lower Grille (If you have TSS sensor in your grille 2020 or newer you may require a grille that accommodates this. Contact your Toyota dealer for the correct part number.
5390135250 Valance Panel (not necessary if you order SR5 bumper cover or cutting to fit winch bumper)
7539235220 Valence Panel Retainer (not necessary if you order SR5 bumper cover or winch bumper)
5213435070 Retaining Bracket, Left
5213335060 Retaining Bracket, Right
5214835120 Stopper, Right (optional, did not install mine)
5202135140 Reinforcement/”Crash bar” (May substitute body armor winch bumper TR19339 or c4 lo pro winch bumper)

5387535150 Front Mudguard, Right (May cut existing mudguard to work)
53876 35150 Front Mudguard, Left (May cut existing mudguard to work)
5216120010 Mud Guard Clips x 6
9015960603 Mud Guard Screws x6
9046707211 Hood Beauty Clips x5 or DORMAN 963634
5329335020 Deflector, Right (Passenger side must be replaced to fit new bumper)
5329435020 Deflector, Left (Drivers side can be left on! So no need to purchase)

*5212935030 Lower Cover skid plate
(May substitute TRD pro skid plate or aftermarket from Car trim home also Greenlane offroad makes a really nice affordable aluminum skid https://greenlaneoffroad.com/)
*9046709227 Lower Cover Clip
(May substitute TRD pro skid plate and hardware aftermarket skids come with hardware)
*9010906330 Lower Cover Bolt
(May substitute TRD pro skid plate and hardware aftermarket skids come with hardware)

Pz32335020 Upper grille garnish (May use aftermarket “Toyota” “4Runner” grill/garnish from https://www.4runnerlifestyle.com/coll...) or Reuse your limited upper grille/garnish as seen in video to save $$